|
<\/div>
GHR-DS<\/span>食用油<\/span>灌裝機<\/span>,<\/span>采用活塞定量方式<\/span>,<\/span>氣壓驅動及電子控制技術<\/span>,<\/span>設計獨特<\/span>,<\/span>操作調試容易簡便<\/span>,<\/span>本機采用雙速控制灌裝流速<\/span>,<\/span>先快裝后慢裝<\/span>,<\/span>即能保證有**的灌裝速度<\/span>,<\/span>又能夠防止灌裝過程的上沖冒溢<\/span>,<\/span>使用氣動內封閉式灌裝閥嘴可有效防止灌裝過程的滴漏。本機輕便靈活<\/span>,<\/span>即可獨立使用也可與壓蓋機、封口機、輸送機聯機使用<\/span>,<\/span>廣泛用于各種油類<\/span>.<\/span>、飲料、調味品、及其它液體產品的定量灌裝。機殼采用不銹鋼制造<\/span>,<\/span>美觀衛生。該機為經濟實用型<\/span>,<\/span>它結構簡單<\/span>,<\/span>易操作<\/span>,<\/span>是中小型企業理想的生產設備。<\/span><\/span><\/p>二、主要技術參數<\/span>:<\/span><\/span><\/p>灌裝容量<\/span>: 0.5—5<\/span>（升）<\/span><\/span><\/p>灌裝速度<\/span>: 200—3000<\/span>桶<\/span>/<\/span>小時（視容量大小、粘度而定）。<\/span><\/span><\/p>灌裝精度<\/span>: <\/span>≤±<\/span>0.5%<\/span>（按設計最大容量計）。<\/span><\/span><\/p>工作電壓<\/span>: 220v<\/span><\/span><\/p>工作壓力<\/span>: 0.4—1.0<\/span>兆帕（需方自備）。<\/span><\/span><\/p>功率<\/span>: <\/span>＜<\/span>300w<\/span>（不包括空氣壓縮機）。<\/span><\/span><\/p>耗氣量<\/span>: <\/span>＜<\/span>0.2<\/span>立方米<\/span>/<\/span>分鐘。<\/span><\/span><\/p> <\/span><\/p>三<\/span>.<\/span>按裝調試<\/span>:<\/span><\/span><\/p>1<\/span>、<\/span> <\/span>首先仔細檢查電器及連接線有無松動脫落。設備在運輸過程中有無碰撞造成損壞或其它螺絲有無松動脫落等現象。<\/span><\/span><\/p>2<\/span>、<\/span> <\/span>分別接通<\/span>220v<\/span>電源<\/span>,<\/span>按通氣路將壓力調整在<\/span>0.4—0.6Mpa<\/span>之間（本機在出廠前已調好）。<\/span><\/span><\/p>3<\/span>、<\/span> <\/span>根據瓶子高度調整好灌裝嘴的高度<\/span>,<\/span>一般瓶口距離灌裝嘴<\/span>5—10<\/span>毫米。根據所要求的灌裝容量調整灌裝量<\/span>,<\/span>通過調整氣缸上帶有容量刻度的磁性開關可改變灌裝容量<\/span>,<\/span>通過量杯或電子稱進行標定<\/span>,<\/span>再細調其精度<\/span>,<\/span>直至符合你的要求<\/span>,<\/span>最大誤差不大于±<\/span>0.5%<\/span>（按設計最大容量計）。根據不同粘度的液體可適當調節灌裝流速<\/span>,<\/span>如粘度大容易起泡沫的液體應減小流速<\/span>,<\/span>可通過調節氣路上的節流閥來改變氣缸的運行速度<\/span>,<\/span>使灌裝流速變小。<\/span><\/span><\/p>4<\/span>、<\/span> <\/span>打開電源開關、按動灌裝開關<\/span>,<\/span>機器便會自動吸液—出液—關閥停止等工作程序。<\/span><\/span><\/p>四<\/span>. <\/span>常見故障的排除<\/span>:<\/span><\/span><\/p>1<\/span>、不工作<\/span>:<\/span>電源未接通或無氣壓<\/span>,<\/span>檢查電源、氣源。<\/span><\/span><\/p>2<\/span>、灌裝容量誤差大<\/span>:<\/span><\/span><\/p>⑴<\/span>、<\/span>料液缸有空氣<\/span>,<\/span>長按工作開關進行排氣。<\/span><\/span><\/p>⑵<\/span>、<\/span>進液管道密封不嚴有漏氣<\/span>,<\/span>卡緊連接管。<\/span><\/span><\/p>⑶<\/span>、<\/span>進液止回閥有臟物<\/span>,<\/span>拆下清洗止回閥。<\/span><\/span><\/p>⑷<\/span>、<\/span>操作或灌裝速度太快<\/span>,<\/span>適當變慢速度。<\/span><\/span><\/p>⑸<\/span>、<\/span>料液缸液位高<\/span>,<\/span>液位應在<\/span>0—1.5<\/span>米（高壓高液位灌裝應另外定制）。<\/span><\/span><\/p>⑹<\/span>、<\/span>料液缸密封圈磨損<\/span>,<\/span>更換密封圈。<\/span><\/span><\/p>
|
在線咨詢 
