| 美國進口INCONEL 718SPF合金棒 718SPF無縫管 |
 |
價格：430 元(人民幣) | 產地：上海 |
| 最少起訂量：1千克 | 發貨地：上海 | |
| 上架時間：2017-06-22 10:37:46 | 瀏覽量：251 | |
布奎實業（上海）有限
 |
||
| 經營模式：生產加工 | 公司類型：國有獨資公司 | |
| 所屬行業：稀有金屬及合金 | 主要客戶：廣泛 | |
 在線咨詢  |
||
| 聯系人:吳女士 (小姐) | 手機:17317769538 |
電話: |
傳真: |
| 郵箱:3255456309@qq.com | 地址:上海市松江區泗磚公路600號 |
|
INCONEL 718SPF 牌號:Inconel 718SPF C(％):≤0.05 Si(％):≤0.35 Mn(％):≤0.35 Cr(％):17.0～21.0 Ni(％):50.0～55.0 Mo(％):2.80～3.30 Co(％):≤1.00 W(％):- Al(％):0.20～0.80 Cu(％):≤0.30 Ti(％):0.65～1.15 Fe(％):余量 其他(％):Nb 4.75～5.25,B≤0.006,N≤0.01,P≤0.015,S≤0.015 INCONEL?alloy 718SPFTMis a specifically “tailored”version of INCONELalloy 718, designed for the super-plastic forming process. The alloy is optimized for theprocess by rigorous control of composition, melt prac-tice and rolling conditions. INCONELalloy 718SPF was developed to meet theneed for a nickel-base alloy suitable for manufactureinto complex shaped components subject to a combina-tion of high temperature, high temperature corrosionand high stress. INCONELalloy 718SPF meets all themechanical property requirements of AMS 5596G, asannealed plus aged, as well as all requirements of AMS5950, which is specific to INCONELalloy 718SPF.Superplastic forming, now highly sophisticated andused extensively for producing commercial and militaryaircraft components, is an ideal process for manufactur-ing complex shaped parts. Use of superplastic formingcan enhance component performance and reliabilitywhile lowering overall manufacturing cost by reducingthe need for extensive welding or other joining meth-ods, lowering the inventory of parts and simplifying themanufacturing process INCONELalloy 718SPF has the same composition andphysical properties as INCONELalloy 718. Limitingchemical composition is shown in Table 1; physicalconstants in Table 2; and elastic properties as a functionof temperature in Tables 3 and 4 on page 3. Thermaland electrical properties are listed in Tables 5 to 7. Thedata in Tables 2 to 7 are typical and can vary slightly,depending on the composition and condition of the testspecimen. INCONELalloy 718SPF is produced with an annealed tem-per. Typical annealed and annealed plus aged properties arepresented in Table 8. The effect of varying gauge on stressrupture life is presented in Table 9 for two aging conditions.The alloy is produced to a grain size of ASTM No. 10 (0.01mm/0.0004 in) or finer. As produced, INCONELalloy718SPF sheet meets the strength and ductility requirementsof AMS 5596G, as annealed plus aged. Table 10 presents data on the tension-tension fatigue-resistance of INCONELalloy 718SPF (ASTM grain size#13), and compares the results with those for conventional-ly produced alloy 718 (ASTM grain size #4.5) in similar testconditions. The axial fatigue testing was carried out at a fre-quency of 59 Hz. INCONELalloy 718SPF possesses two essential character-istics that make the alloy amenable to superplastic forming:Grain size stability over the time and temperature regime employed for superplastic forming (See Figure 1).Acombination of low flow stress and significant ductility using typical superplastic forming process conditions (See Figure 2).The effect of lower temperatures on flow stress and totalengineering strain at constant strain rate is depicted in Figure3. For the typical initial strain rates currently employed forsuperplastic forming, the expected range of engineeringstrain for INCONELalloy 718SPF is given in Figure 4. Theeffect of lower temperatures on the engineering strain as afunction of the initial strain rate is shown in Figure 5. Forthe same initial strain rates, the expected true stresses forINCONELalloy 718SPF are given in Figure 6 and for lowertemperatures in Figure 7. The superplastic forming process for INCONELalloy718SPF involves the shaping of sheet between ceramic ormetallic platens at temperatures near 1750°F (954°C). Thesheet is subjected to an inert gas pressure of about 300 psi(2.1 MPa) for periods up to four hours. Table 13 compares the annealed properties of INCONELalloy 718SPF with that of superplastic alloy formed materi-al with reductions in gauge of 13%, 19% and 33%. Notethat, under these conditions, the alloy exceeds the maximumannealed strength requirements of AMS 5596G but not theminimum requirements for ductility and hardness. This islargely due to the ultra-fine grain size of the material whichremains essentially constant during superplastic forming.While grain size remains constant, increasing deformationas a result of the superplastic forming process reduces hard-ness, tensile strength and elongation. Table 14 shows the effect of annealing time (0.33 and 1.0h) at 1750°F (954°C) on restoring aged room temperaturetensile ductility (the minimum elongation of AMS 5596G is12%). Tensile properties and hardness are satisfactory, asare all tensile properties at 1200°F (649°C) for the timesevaluated. Because of the fine grain size of the post-super-plastically formed material, it is not possible to achieve thestress rupture life of AMS 5596G without incorporating agrain growth annealing step prior to the aging heat treat-ment, as indicated in Table 15. HIPing (hot isostatic pro-cessing) of superplastically formed components may beespecially advantageous for enhancing stress rupture andfatigue properties. Like most nickel alloys, INCONELalloy 718SPF is subjectto cavitation. As shown in Figure 10, the area of cavitation,while minimal at elongations of less than 150%, increasessignificantly with increasing elongations beyond 200%.Decreasing strain rates at any given elongation also increasethe area of cavitation. The area of cavitation for two initialstrain rates and total strains of less than 200% are presentedin Table 16 along with the average cavity size for each totalstrain. Use of background pressure during the superplastic form-ing operation is an effective method for reducing cavitation.Cavitation data as a function of maximum true strain andbackground pressure are presented in Figures 11 and 12 forinitial strain rates of 1 x 10-4s-1and 3 x 10-5s-1, respectively.Hot isostatic pressure exposure at 1750°F (954°C) and 15ksi (103 MPa) has been found to eliminate cavitation insuperplastically processed sheet that has been reduced 33%in thickness. ========================= 銷售熱線1：021-67899177 銷售熱線2;021-67899277 銷售熱線：17317169538 銷售熱線：17317769538 公司傳真：021-67899177 V信： 17317169538 v信： 17317769538 QQ： 986692047 QQ: 3255456309 QQ： 2318842260 =========================== 上海布奎實業有限公司優勢特點： 1、強大的價格優勢；因為我們是行業內很多世界知名品牌的直接合作商，在原料的成本價上省去了很多不必要的費用。 2、快捷的供貨流程；在客戶確認好訂單，合同生效之后，一般都可在1-2個工作日內完成下單、備貨、出庫、發貨等工作，將客戶所需的材料第一時間送達，想客戶之所想急客戶之所急！ 3、貼心的售后服務；相較于前期銷售，上海布奎更關注的是客戶訂購材料后的使用情況；有需要的話，上海布奎公司會根據客戶的實際情況安排專業的技術人員威行專門的材料使用指導；在材料使用過程中，如果客戶碰到任何關于材料的疑異問題均可在第一時間得到處理。
|
| 版權聲明：以上所展示的信息由會員自行提供，內容的真實性、準確性和合法性由發布會員負責。機電之家對此不承擔任何責任。 友情提醒：為規避購買風險，建議您在購買相關產品前務必確認供應商資質及產品質量。 |
機電之家網 - 機電行業權威網絡宣傳媒體
關于我們 | 聯系我們 | 廣告合作 | 付款方式 | 使用幫助 | 會員助手 | 免費鏈接Copyright 2026 jdzj.com All Rights Reserved??技術支持：機電之家 服務熱線：0571-87774297
網站經營許可證:浙B2-20080178
